AndCoat HB 'Low Temp' Solvent Free Epoxy
                              £114.00 (inc. VAT)
                              £95.00 (ex. VAT)
                            
- Free worldwide shipping
 
- In stock, ready to ship
 - Backordered, shipping soon
 
AndCoat HB LT is a solvent-free, high-build two-pack epoxy coating formulated for use in colder conditions. Designed to cure at lower temperatures, it provides the same outstanding durability, adhesion and chemical resistance as standard AndCoat HB, but with extended working times that make it suitable for winter application.
This coating delivers a smooth, gloss finish with exceptional resistance to water, oils, fuels and many chemicals. It is ideal for use on concrete floors, steelwork, bunds, tank linings and other industrial surfaces where both high performance and cold-weather application are required.
Surface Preparation
For best results, substrates must be sound, clean and free from contaminants:
- 
Concrete & Masonry: Minimum 28 days cure, dry and structurally sound. Remove laitance, dust, oil, grease and other contaminants by vacuum blasting or grinding. Repair surface defects before application.
 - 
Steel: Blast clean to SA 2½ (ISO 8501-1) or equivalent, producing a sharp profile. Coat immediately after preparation to avoid flash rusting. If blasting is not possible, mechanically prepare to St3 standard.
 - 
Previously Coated Surfaces: Remove any unsound coatings. Abrade sound coatings to provide a key.
 - 
All surfaces must be clean, dry and free from moisture before application.
 
Technical Data
- 
Type: Two-pack solvent-free epoxy (low-temperature cure)
 - 
Finish: Gloss, high-build
 - 
Colours: Range of colours available
 - 
Mix Ratio: 4:1 by volume (Base : Hardener)
 - 
Volume Solids: Approx. 100%
 - 
Film Thickness:
- 
Wet: 200–500μm per coat
 - 
Dry: 200–500μm per coat
 
 - 
 - 
Theoretical Coverage: 4–5m²/litre at 250μm DFT (practical coverage will vary)
 - 
Pot Life: 45–60 minutes at 10°C (shorter at higher temps)
 - 
Overcoating Interval: Minimum 16 hours, maximum 72 hours at 10°C
 - 
Full Cure: 7–10 days at 10°C
 - 
Chemical Resistance: Excellent against oils, fuels, water and many chemicals
 - 
Heat Resistance: Up to 60°C (dry heat)
 - 
VOC: Solvent-free
 
Directions for Use / Application
- 
Mixing: Add Hardener to Base in the specified 4:1 ratio. Mix mechanically with a slow-speed drill and paddle until uniform. Only mix what can be applied within the pot life.
 - 
Application Methods: Suitable for brush, roller or airless spray. Apply in even coats, avoiding puddling.
 - 
Environmental Conditions:
- 
Substrate & ambient temp: Min 5°C (up to 20°C)
 - 
Surface must be at least 3°C above dew point
 - 
Maximum RH: 85%
 
 - 
 - 
Overcoating: Recoat between 16–72 hours at 10°C. If maximum interval is exceeded, abrade to provide a key.
 - 
Curing: Full chemical cure achieved after 7–10 days at 10°C.
 - 
Cleaning: Use AndCoat Thinner or suitable solvent to clean tools and equipment immediately after use.
 - 
Storage: Keep in original unopened containers in a dry, well-ventilated area between 5°C and 35°C, away from direct sunlight.
 
Data Sheets
Use collapsible tabs for more detailed information that will help customers make a purchasing decision.
Ex: Shipping and return policies, size guides, and other common questions.